Produkty dla dostawcy żywicy pu (10)

Wenn Sie ein widerstandsfähiges Kunststoffprofil benötigen, ist der Werkstoff Polyphenylensulfid die perfekte Lösung für Sie. Ein PPS-Kunststoffprofil hält hohen Temperaturen, Druck und der Einwirkung von aggressiven chemischen Substanzen stand. Dieser Hochleistungskunststoff bietet sich vor allem für Anwendungen in den Branchen Automobil, Elektronik, Luftfahrt und Gebäudeausstattung an. Alle notwendigen Normen und Spezifikationen werden von ihm in diesen Bereichen umfassend erfüllt. Dieser Kunststoff ist von Haus aus flammwidrig und somit ein V-0 klassifiziertes Material nach der Brandschutznorm UL94

Syntech HAG Acryl Syntech HAG Acryl is a four-component resin that reacts to form an elastic and durable gel. The properties of Syntech HAG Acryl are: • Good general chemical resistance. • Does not contain acrylamide, methacrylamide, formaldehyde or solvents. • Not inflammable. • Excellent adhesion on mineral building materials such as concrete, cement and bricks. • The reaction speed can be adjusted from a few seconds to several minutes. • When the injected cracks dry out due to temperature or groundwater level fluctuations the gel does not crack easily. • The hardened gel has excellent durability in wet-dry cycles. Syntech HAG Acryl components are supplied ready to use. Create 2 mixes in separate plastic buckets. Prepare only the quantity to be used each time. Solution 1: Syntech HAG Acryl component A (25 kg resin) mixed with Syntech HAG Acryl component B (2.5 kg catalyst). Solution 2: Syntech HAG Acryl component C (2 packs of 0.625 kg) mixed with clean tap water. Attention: The amount of water must be equal in volume to solution 1. When mixing resin, always use a wooden or stainless steel spatula. The reaction time depends on the temperature of the material, the structure of the building and the possible amount of water present. Higher temperature will speed up the reaction time and lower temperature will slow it down. It is advisable to carry out an on-site test, before injection, to observe and define the reaction time. To change the reaction time, only adjust the amount of Syntech HAG Acryl component C. The amount of the other components remains the same. Use a two-component stainless steel pump (manual, electric or pneumatic). Check that the pump and equipment are clean and that there is no residue from previous injection work. The two mixtures are fed into the pump separately, but are mixed homogeneously at a volumetric ratio of 1:1 in the pump's mixing head, before being injected through the pump nozzle. Check the quality of the concrete, as injection involves pressure. Sealing and waterproofing of cracks and cavities in walls, floors, concrete constructions, underground structures, etc. It can be used in constructions that are not permanently in contact with water (fluctuating groundwater level). Injection of very fine cracks. Determine the type and size of packers based on your pump and injection type. If reinforcing steel is present, try to locate it and plan the drilling pattern so that the reinforcement is not drilled. Drill holes at an angle of approximately 45° or less and in the direction of the crack. Make sure the hole goes through the crack. The distance of the drilled holes depends on the width of the crack. Place the packer in the hole. Prepare the pump to start the injection. The injection pressure varies depending on the structure and size of the crack. Start the injection at the lowest point of the crack. Continue injecting until resin flows out of adjacent packer(s). This is necessary to achieve uniform distribution of the material. Stop pumping, unplug and move on to the next packer. Continue the procedure until the crack is completely filled. After the material has cured, the packers can be removed. Holes drilled can be covered with Repar Tix Speedy HP quick-setting mortar. Clean and rinse the pump equipment with water whenever there is a stoppage longer than 15 minutes and, after completing the injection, rinse with a sufficient amount of water. Make sure the pump is clean and stop only when clean water comes out of the pump. The consumption of the product depends on the size of the empty volume to be filled. Can 25 kg [A] - Plastic can 2.5 kg [B] - Canister 0.625 kg [C] - Canister 0.625 kg [D] - Kit: 1 Can 25 kg [A] + 1 Plastic can 2.5 kg [B] + 1 Canister 0.625 kg [C] + 1 Canister 0.625 kg [D]

Polyimide Resin Polyimide Resin Powder are known for thermal stability, good chemical resistance, excellent mechanical properties, and characteristic orange/yellow etc color.Thermoset polymer matrix polyimides exhibit very low creep and high tensile strength. These properties are maintained during continuous use to temperatures of up to 360 °C. Composite Polyimide Resin Powder (PTFE composite wholly aromatic polyimide resin powder) It is used for compounding with polytetrafluoroethylene (PTFE). Generally, the addition amount is 5%-15%, which can greatly improve the wear resistance of PTFE and slightly improve the heat resistance of PTFE.Characteristics: High temperature resistance, self lubrication, friction resistance, easy processing. Application: Bearing, shaft, bearing, seal gasket, etc. Yancheng Tiandi Insulation Co.,Ltd web :https://www.polyimide-pi.com/polyimide-powder-varnish.htm mail: hsinsulation@aliyun.com hsinsulation@hotmail.

für Extrusionsanwendungen in den Farben: natur weiß bunt schwarz für Spritzgussanwendungen: HDPE Mfi 3-5 Regranulat HDPE Mfi 4-7 Regranulat HDPE Mfi 6-8 Regranulat in bunt und schwarz

HDPE GRANÜL, BORU ÜRETİMİ İÇİN İDEAL. İSTENEN MFI DEĞERLERİNDE. SİYAH, GRİ, MAVİ, BOYASIZ SEÇENEKLERİ İLE.

PDM granül kauçuktan üretildiği için oldukça esnek bir maddedir. Bu nedenler her türlü şarta kolaylıkla ayak uydurabilir. Yazın güneşi ya da kışın soğuğu bu malzemeye hiçbir şekilde zarar veremez. Elastik olmasından dolayı darbelere karşı oldukça fazla dayanıklıdır. Elastik olması malzemenin her şekle girmesine de yardımcı olur. Yapısı gereği çok dayanıklı bir ürün olan EPDM granül, öyle hava şartlarına göre değişiklik göstermez. Her duruma dayanıklı olan bu malzemede esneme, genleşme, büzülme gibi olaylar asla yaşanmaz. Bu sayede yaz sıcağında ve kış soğuğunda kolaylıkla kullanılır. EPDM sonradan renklendirilen bir madde değildir. Boyama yöntemi kullanılmayan bu malzemede renk solması gibi bir durum asla yaşanmaz. Yıllarca renkleri bozulmadan kalabilir. Bu malzemede aklınıza gelebilecek her rengi kullanabilirsiniz. Geniş bir renk seçeneğine sahip olan EPDM granül size istediğiniz rengi seçme şansını verecektir.

Das Gummi NP- Granulat ist frei von kanzerogenen N- Nitrosaminen und Weichmachern.

Nummer Eins chemicals 2008 Yılından beri Kimya sektöründe edinmiş olduğu tecrübeler ışığında müşterilerine en iyi ürünü ve hizmeti sunma felsefesi ile yola çıkarak İSTANBUL tuzla’da A.O.S.B de Epoksi ve Poliüretan Yapı Sistemleri, Antikorrozif epoksi ve poliüretan çelik konstrüksiyon ürünleri, Ahşap ve Metal tekneler için epoksi ve poliüretan ürünler, Su bazlı polimer esaslı su yalıtım sistemleri İç ve Dış mekanlarda kullanılan kaplama sistemlerine yönelik ürünlerin üretimine devam etmektedir. Firmamız kaliteli üretim kaliteli ürün anlayışı ile Avrupa normlarına uygun laboratuar cihazları ve analiz ekipmanlarına sahip ARGE ve Kalite Kontrol Laboratuvarında konusunda uzman mühendis ve kimyager kadrosu ile günümüz dünyasındaki teknolojik gelişimleri yakından takip ederek ürünlerini sürekli geliştirmekte ve yenilikçi bir anlayış ile çalışmalarını sürdürmektedir.

Il metodo Airless garantisce una verniciatura ad altissima resa senza formazione di nebbia. Grazie all’elevata pressione di esercizio e a portate ai vertici della gamma, questo modello ti consente una velocità di esecuzione davvero sorprendente. Punto di forza della pompa Airless serie Testarossa mod. Superdiecimila è il suo raggio d’azione che arriva a 70 metri, sia in orizzontale che in prevalenza, permettendoti di non perdere tempo nel dover spostare la macchina durante l’utilizzo. La pompa si adatta a diversi tipi di lavorazione: dall’edilizia all’industria, dalla falegnameria alla carpenteria. I prodotti spruzzabili sono: smalti, vernici, antiruggine, primers, pitture lavabili, pitture silossaniche e al quarzo, tempere, incapsulanti per l’amianto, intumescenti, bicomponenti, resine epossidiche e molti altri.

Silicon nitride is one of the hardest ceramics but also one of the most resistant. Si3N4 is mainly used in severe environments which combine extreme temperatures with abrasive and/or corrosive medium. Silicon nitride can be of different grades : sintered, hot pressed or reaction bonded. Selection of materials Microcertec offers two high-purity Si3N4 grades that are particularly suited for hostile environments : sintered silicon nitride hot pressed silicon nitride Both Si3N4 materials are mainly designed to be used in thermal-mechanical or corrosion-resistance applications because they show an outstanding behaviour to resist to wear, thermal shocks and corrosion (liquids and gases). Moreover, these pure Si3N4 grades offer a low thermal expansion. Properties Sintered silicon nitride and HP Si3N4 have the following properties : low density excellent thermal shock resistance excellent wear resistance excellent corrosion resistance (liquids and gas) low coefficient of thermal...